Skip to content

Furnace Repair in Burbank, CA

Serving Burbank and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (213) 410-0763

The short answer

AdvancedAir Contractors repairs gas furnaces and heat pumps in Burbank ZIP codes 91501, 91502, 91504, 91505, and 91506. Most problems trace back to a furnace that sat idle for months, such as a dirty flame sensor, a failed igniter, or a clogged filter. If replacement is on the table, check South Coast AQMD furnace rules and your utility's current rebate offers first.

Burbank winters are mild, so a furnace can sit unused from spring through fall and then get switched on during the first cold snap of the season. That long idle stretch causes many of the heating problems we see in Burbank homes: dust on the burners, weak flame sensors, sticky ignition, and filters nobody has checked since last winter. AdvancedAir Contractors repairs gas furnaces and heat pump systems in homes across Burbank, including ZIP codes 91501, 91502, 91504, 91505, and 91506. We're based in Reseda, about 13 miles west, so we're a short drive from most Burbank streets. This page covers the furnace problems we see most often in Burbank, what you can check yourself before calling, and what to think about if your repair turns into a replacement.

Why Burbank Furnaces Act Up at the Start of the Season

Burbank sits inland, where summers run much hotter than near the coast and winters stay mild. Your furnace may only run on cool evenings and early mornings, and it may sit untouched for half the year. During that time, dust settles on the burners and heat exchanger, small parts like flame sensors collect residue, and pilot or ignition components can weaken without anyone noticing.

A burning smell for the first few minutes of the season is usually that dust cooking off, and it should fade quickly. If the smell lingers, the furnace starts and shuts off over and over, or it won't light at all, that's when a repair visit makes sense.

Common Furnace Problems We Repair in Burbank

These are the issues that account for most of our heating calls in Burbank homes:

  • Furnace clicks or tries to light but never fires: often a failed hot surface igniter or a gas valve problem
  • Burners light, then shut off within seconds: usually a dirty or failing flame sensor
  • Blower runs but the air is cold: ignition, limit switch, or thermostat setting issues
  • Short cycling, where the furnace turns on and off frequently: overheating from a clogged filter, a blocked return, or a faulty limit switch
  • Loud banging, rumbling, or squealing: delayed ignition, a worn blower motor, or a loose belt or panel
  • Some rooms warm, others cold: duct leaks, closed or blocked registers, or an undersized blower setting
  • Error codes flashing on the control board: we read the code and test the part it points to before replacing anything

What to Check Before You Call

A few simple checks can save you a service visit, or at least help us diagnose the problem faster when we arrive.

  • Make sure the thermostat is set to Heat, set above room temperature, and has working batteries if it uses them
  • Check that the furnace power switch, which often looks like a light switch near the unit, is on
  • Look at the air filter and replace it if it's gray or clogged
  • Confirm the furnace access panel is fully closed, since many units won't run with it loose
  • Look for a blinking light on the control board and write down the pattern
  • If you smell gas, leave the house and call your gas utility or 911 from outside before calling anyone else

Repair or Replace? Rules and Rebates to Know in the Los Angeles Region

Most furnace problems can be fixed with one part and a cleaning. When a heat exchanger is cracked, the unit is very old, or repairs keep stacking up, replacement may be the better choice. We'll explain what we found and let you decide.

If you're replacing a gas furnace in Burbank, South Coast AQMD Rule 1111 matters. It limits NOx emissions from natural-gas central furnaces sold and installed in this region, and the district has been amending it toward zero-emission requirements. Because the district sets and revises the compliance dates, check the current rule before you buy. We can walk you through how it applies to your system.

Many homeowners look at a heat pump instead. Rebates for heat pumps depend on which utility serves your address. Burbank homes aren't all on the same utility as neighboring cities, so we confirm the current offer for your address before quoting it. Note that the federal 25C tax credit for heat pumps only covered systems placed in service before December 31, 2025, so it doesn't apply to installations now.

Burbank and Nearby Service Areas

We handle furnace repair throughout Burbank, from the flats near the airport to the hillside streets where homes sometimes have furnaces in tight attics or crawlspaces. We also serve nearby areas, including Los Angeles, San Fernando, West Hollywood, Beverly Hills, and Santa Monica. When you call, tell us your furnace's location, its symptoms, and any error codes, and we'll come prepared with the most likely parts.

More services in Burbank

Related

What to expect

How a visit goes

  1. We find the cause first

    Before we recommend anything, we test the system and track the symptom back to its source. That way you pay to fix the actual problem, not to replace parts until something works.

  2. We explain your options clearly

    You'll hear what we found, what it means for your system, and the choices you have, including whether a repair or a replacement makes more sense for the equipment's age and condition.

  3. We check the local details

    Furnace emissions rules and equipment rebates in Southern California depend on the district and on which utility serves your address. We confirm what currently applies to your home before you make a decision.

FAQ

Common questions

Why does my furnace smell like burning when I first turn it on?

After months of sitting idle, dust settles on the burners and heat exchanger. It burns off in the first few minutes of use. If the smell doesn't fade, or smells like electrical burning or gas, turn the system off and call for service.

My furnace lights and then shuts off right away. What causes that?

The most common cause is a dirty or failing flame sensor. The furnace can't confirm a flame is present, so it shuts off the gas as a safety measure. Cleaning or replacing the sensor usually fixes it.

Do you repair heat pumps as well as gas furnaces?

Yes. We repair both gas furnaces and heat pump systems in Burbank homes.

Can I get a rebate if I replace my furnace with a heat pump?

It depends on the utility that serves your address. We confirm the current rebate offer for your address before quoting it. The federal 25C credit no longer applies to new installations after December 31, 2025.

Are there rules about installing a new gas furnace in Burbank?

Yes. South Coast AQMD Rule 1111 limits NOx emissions from gas furnaces installed in the Los Angeles region, and the district has been moving it toward zero-emission requirements. Check the current compliance dates before buying a replacement.

Which Burbank ZIP codes do you serve?

We serve 91501, 91502, 91504, 91505, and 91506, plus nearby areas like Los Angeles, San Fernando, West Hollywood, Beverly Hills, and Santa Monica.

Tell Us What Your System Is Doing

Whether it's warm air from the vents, a furnace that won't stay lit, or a strange noise you can't place, describe the problem and we'll set up a visit to diagnose it and walk you through your options.

Call (213) 410-0763 Request Service